Shijiazhuang Zhongqian Pump Industry Co., Ltd. · Slurry pumps / Spare parts / Technical support
ZQZhongqian PumpZHONGQIAN PUMP
Home/Products/Shafts & Shaft Sleeves
PRODUCTS · SHAFTS & SHAFT SLEEVES

Shafts & Shaft SleevesTorque transmission and shaft protection: the sleeve is the most overlooked wear part

The shaft transmits motor torque to the impeller. The shaft sleeve fits over the shaft under the seal and takes the friction and slurry attack instead of the shaft itself. It is inexpensive, but it protects a much more expensive component.

Sleeve and shaft failures usually start at the seal: over-tightened packing, interrupted flush water, or solids entering the seal chamber will groove the sleeve first and then damage the shaft and bearings.

Slurry pump shaft sleeve
Shafts & Shaft Sleeves
SCOPE

What this category covers

Part / structureDescription
Pump shaftTransmits torque and carries radial and axial loads
Shaft sleeveProtects the shaft under packing, mechanical seal or expeller
Spacer / locating sleevePositions the impeller and sleeve axially
Release ring and lock nutRetain the impeller and allow clearance adjustment
MATERIALS

Typical materials for each part

PartFunction in the pumpTypical material
ShaftThe pump shaft transmits motor torque and supports the impeller. Adequate strength, stiffness and fatigue resistance are required; straightness directly affects vibration and bearing life.Quality alloy steel or quenched-and-tempered carbon steel, with the seal section protected by a shaft sleeve.
Shaft SleeveThe shaft sleeve fits over the pump shaft and isolates it from packing friction or mechanical seal contact and from corrosive media. It is one of the most frequently replaced seal-area parts.Wear-resistant alloy, stainless or 3Cr13-type martensitic steel, often hardened or coated; rubber-covered versions also exist.
Spacer SleeveThe spacer fixes the axial position of the shaft sleeve, bearings and impeller so the assembly dimension chain is correct.Steel or stainless steel with flat, burr-free end faces.
Lock NutThe lock nut secures the impeller, bearings or coupling components against loosening from vibration and shock.Carbon or stainless steel with a locking feature.
Impeller Release RingThe impeller release ring provides a bearing surface for removal, protecting impeller threads and the shaft end during on-site wear part changes.Quenched-and-tempered steel or stainless steel with sound threads.
Bearing AssemblyThe bearing assembly supports the shaft under radial and axial loads and governs rotor stability. A cartridge design can be removed as a unit to adjust impeller clearance.Heavy rolling bearings (cylindrical roller plus thrust/angular contact combination) with steel shaft and housing.
SELECTION

Matching structure and material to the duty

Common combinations; grade choice needs medium temperature, concentration and particle size.

Duty conditionRecommendation
Packing with neutral slurry3Cr13 type martensitic stainless sleeve
Abrasive duty with visible wearSurface-hardened or sprayed sleeve, or high-chrome
Mechanical sealFiner surface finish to suit the seal faces
Corrosive mediumDuplex stainless or corrosion-resistant alloy sleeve
MATCHING RANGE

Matching series and models

Model pages list construction, code explanation and chart extracts.

AH series
ZJ series
ZGB series
SP series
HH series
G series
DT series
RELATED PARTS

Parts in this category

Each part has its own page with basic number, material and matching range.

FAILURE MODES

How these parts fail and what to do

Judge by wall thickness, clearance and performance, not by months in service.

FAQ

Shafts & Shaft Sleeves questions

Can a worn sleeve be welded and re-machined?

Not recommended under the seal. Welding changes concentricity and hardness, so a new sleeve is more reliable and usually cheaper.

Does the pump head have to come off to change a sleeve?

On most constructions yes, after removing the impeller. The series manual gives the sequence; AH, ZJ, SP and ZGB manuals are readable on this site.

Must shaft and sleeve be replaced together?

No. If the journal is sound, only the sleeve is replaced; if the journal is damaged, the shaft must be assessed for repair.

Inquiry

Send a model or worn-part dimensions

Parts are supplied by basic part number because the same name has different numbers in different frames. Send the pump model, frame code and a photo of the worn part, or the basic number directly.

Ask about Shafts & Shaft Sleeves

We reply within one business day. You can also call +86 188 0321 2220.

Your details are used for this inquiry only.

Model and spare part identification

Please provide the pump model, nameplate data and duty parameters by phone or email. Performance charts and manuals can be read online.

Click outside or press Esc to close
☎Call✉Email⇄Inquiry